Yes, 

and this compatibility has been attested for some of our products by an independent Control Board in France which has issued a New Technology Investigation (NTI) for some and a Technical notice (ATec) for others to confirm this. 

 

The DualSun FLASH and SPRING panels are therefore compatible with SOPRASOLAR's FIX EVO and FIX EVO TILT system. A layout verification and a calculation note should be made by SOPRASOLAR to validate the use of the system on the project : 

• Roof types: Flat roof
• Certification: 
  • NTI : CPP DT N°17/003_EN_Ind_00
  • ATEC :  21/21-75_v1
• Possible layouts: Portrait and Landscape

 

You can also consult the FIX EVO TILT system documents available on the SOPRASOLAR website.

To consult the compatibility of the DualSun Spring and Flash panels with flat roof installation systems: Compatibility table - Flat roof

For more details about the installation of DualSun panels on the roof : What mounting systems can be used to install DualSun Spring panels?

 

 

Details for installers :

 

Modules Technical name	DSTNxxxG1-360SBB5 (xxx=370-400) DSTIxxxG1-360SBB5 (xxx=370-400)
Commercial name	SPRING 375 Shingle Black Insulated and Non-Insulated SPRING 400 Shingle Black Insulated and Non-Insulated
Mounting system	SopraSolar Fix Evo Tilt
Date	27.01.2022

In order to facilitate the connection of the DualSun hydraulic connections in landscape mode, it is recommended to install the DualSun Spring modules on the SOPRASOLAR FIX EVO TILT system as follows :

When the junction box is positioned downwards :

 

Position the bottom of the panel 50 mm from the bottom of the small block bracket.

 

 

When the junction box is positioned upwards :

 

Position the top of the panel 50 mm from the top of the big block bracket.

 

Hydraulic connections 

 

 

The hydraulic connections can be attached to the modules or to the SOPRASOLAR FIX EVO TILT studs to prevent them from resting on the roof surface. Clips are delivered with the DualSun Inlet/Outlet connection kits to attach the hoses to the frame return of the SPRING modules. 

The hydraulic transfer lines between the technical room and the DualSun SPRING panel field are to be raised in the same way as the electrical cables and run in cable trays.

 

Modules Technical name	S315BN-60 S315BI-60
Mounting system	SopraSolar Fix Evo Tilt
Date	24.07.2022

 

The installation of the SPRING 280 to 315 modules in portrait mode does not present any particularity.

 

The installation of SPRING 280 to 315 modules in landscape mode requires a few precautions:

 

In order to facilitate the connection of the DualSun hydraulic connections in landscape mode, it is recommended to install the DualSun SPRING 280 to 315 modules on the SOPRASOLAR FIX EVO TILT system as follows:

• Shift the modules as far as possible towards the lower studs if the junction box is on the right when looking at the front of the panel (within the limit of the positioning of the bracket on the frame).
• Shift the modules as far as possible towards the upper studs if the junction box is on the left side of the front panel (within the limit of the positioning of the bracket on the frame).

Landscape mode " SOUTH "  Junction box on the right when looking at the front panel	Landscape mode " SOUTH "  Junction box on the left when looking at the front panel
Tilting direction of the photovoltaic module
Offset direction of the modules to facilitate hydraulic connections

 

The clamp may be at the frame limit, but the entire range of the clamp must be applied to the module, in accordance with the permissible mounting ranges in the "DualSun SPRING Installation, Operation and Maintenance Instructions". This positioning does not affect the mechanical performance of the module.